cleaning diagram of small fume purifier

cleaning the range hood purifier is not easy for hotels, apartments, etc. even cleaning the range hood purifier used at home is extremely troublesome. first, what is the cleaning order and precautions to use. what is the cleaning of the range hood purifier? what steps should be followed for cleaning? these two issues are secondary to snow cat cleaning. snow cat cleaning takes only three tricks to clean the range hood purifier.

1.before disassembling and washing the range hood, wet your hands with water, apply soap on your hands, especially some in your nails, and then wipe your hands dry. wash it with water and soap after get off work, so there will be no putty on your hands. cleaning the range hood purifier usually starts with the oil storage box, sprinkle a thin layer of soap powder on the oil storage box, and then inject about one-third of the water to allow the recovered oil to float on the water surface, and then pour it out and then do the same. or you can put a small disposable oil box in the oil storage box. after slowly collecting the gutter oil, take it out and throw it away.

2.clean the body: first, cut off the power supply of the smoker to ensure the most basic life safety. use a screwdriver to remove the screws from the housing and remove the housing and oil mesh. if the oil on the oil net is thick, use a tool to gently scrape off the excess oil, then put it in warm water mixed with neutral detergent, soak for three minutes, and then wipe it with a clean rag.

3.fan blade cleaning: in addition to cleaning with oil smoke, you can also use dishwashing liquid to vinegar mixed liquid to prevent pollution to the human body. if the grease is too thick, you can wrap some fine wood chips in cotton yarn, or wipe it directly with your hands. the thicker the oil, the easier it is to wipe off. after wiping, clean it with water and dry it, and then it can be assembled to ensure that the range hood is as clean as new. there is also a high-pressure steam method. the specific method is: put half a pot of cold water into a pressure cooker, heat it, remove the pressure valve when continuously discharge the steam, open the range hood to align the steam water column with the rotating air blades, and the oily sewage will flow into the waste oil tank along the discharge tank. the turbine of the range hood can also be handled in the same way.

1。it may be because there is no electric field to dry after cleaning. if the electric field is cleaned and put back into the box without drying, there are still many water droplets inside the electric field. if the electric field generates high voltage when powered on, the local voltage will become unstable due to the spots of the water droplets, resulting in a burst sound of discharge and ignition.

2.it may be that foreign objects were not removed during the cleaning process. when cleaning the electric field of the oil fume purifier, if the internal foreign objects are not removed and the foreign objects are stuck between the electric field plates, we clean them and put them back. after power on, the position of the foreign objects will affect the voltage balance of the electric field, resulting in ignition and burst sounds.

3.it may be that the plate is accidentally deformed during cleaning. during cleaning, we need to disassemble the electric field, which may cause bumps and deformation during the handling process. after cleaning, put it back, the distance between the deformed plates changes, causing the two plates to be fired and discharged, making a burst sound.

how to clean the oil fume purifier? after using it for a period of time, the actual effect of cleaning the oil fume purifier is significantly reduced due to the oil stain inside. therefore, during the service life of the electrostatic induction fume purifier, the electrostatic induction fume purifier should be maintained and cleaned immediately. ensure the purification efficiency of the oil fume purifier. the electrostatic fume purifier must be cleaned every three months. if there is too much oil, there will always be fire accidents.

1. preparation of cleaning agents:

1.pour the detergent into a jar filled with 40-50 boiling water at a ratio of 3%, stir to melt thoroughly.

2、the industrial caustic soda and water are equipped with necessary cleaning agents at 1; 5%.

3.special organic chemical cleaning agent for electrostatic induction fume purifier.

how to clean the oil fume purifier?

2. cleaning method:

processing net cleaning:

1.disconnect the switch power and open the maintenance door.

2.drag the preliminary processing network out.

3.soak in the cleaning tank for ten minutes and gently wash away the oil.

4.place the dry and dry pretreatment net in situ into the electrostatic induction fume purifier.

3. electrostatic field cleaning:

1.disconnect the switching power supply, open the maintenance door, and clear the static field.

2.put the cleaning tablet (plastic board )place it in the middle of the electric board, stick it on the electric board, and move it from top to bottom. you just need to remove most of the oil stains on the electric board. it can be cleaned up at one time or multiple times.

3.remove the scraped oil stains and wash them with cold water.

4.of course, the electrostatic field after cleaning is blow-dry (if there are still a small amount of oil stains, it will not easily endanger the actual effect of product cleaning )。

5.put the dry electrostatic field into the fume purifier in its original position, close the repair door and work again.